We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

AR# 3090

FPGA Configuration - Run times for configuration rates and CPLD programming


Keywords: XC3000, XC4000E/EX, XC5000, XC9500

Urgency: Standard

General Description:
What are the Xilinx configuration rates/programming times for FPGAs and CPLDs?



Any Xilinx FPGA can be configured and reconfigured in several different modes. The fastest is called Slave Serial, where an external clock is provided that shifts in the serial configuration data. Slave Serial, which reduces the power-up delay, allows for an external clock rate of 10 MHz maximum. Other modes can be up to 15 times slower. The following description doesn't include the power-up cycle of the FPGA. For further details, read the resolution that covers the more involved details and calculations (Power-on delay).

In configuration modes that use the internal CCLK, such as Master Serial, the internal CCLK is subject to variations with process, temperature and power supply. In older Xilinx families (XC3000A family) the serial data stream rate is limited to this internal 1 MHz, in the newer families ( XC4000 and XC5200 families ) it is selectable between 1 MHz (nominal) and 8 MHz (nominal) rate (using the fast configuration mode), and can be driven at up to 10 MHz. In the default slow mode, the frequency ranges from 0.5 MHz to 1.25 MHz. In the fast CCLK mode, the frequency ranges 4 MHz to 10 MHz.

The number of bits varies with device size: 14,779 bits for the smallest XC3000 device (XC3020) to 5,433,888 bits for the presently largest XC4000 device (XC40250XV).

To use the internal 8 MHz (nominal) CCLK:

5.2.x : makebits -f ConfigRate:Fast design.lca
M1.x : bitgen -g ConfigRate:Fast design.ncd

NOTE: The XC3000 does not offer this option. This comes to 10 to 20 bits per gate.

Configuration times are thus between 10 ms and 544 ms, if you use the faster clock rate for the bigger devices. Byte-parallel configuration modes are not any faster, since they operate byte-to-serial conversion within the chip. The exception is the XC5200 Express mode that accepts byte-wide date at 10 MHz, thus configuring the XC5215 with 237,744 bits in about 4 ms.


Application Note (Xilinx XAPP068): "In-System Programming Times" discusses XC9500 device programming times.


Here are the more involved details and calculations (XC3000, 4000E/EX and 5200):

1. The FPGA becomes active internally at about 3.5 volts. For the XC4000, there is a built-in power-on delay that waits an additional 64 ms for power to all the devices on the board to become stable (it's only 16 ms if the FPGA is configuring in peripheral or slave mode). For the XC5200 devices, there is no distinction between master and slave modes with regard to the power-on delay. A power-on delay of 4 ms (nominal) is applied in the XC5200 family of devices. When all the /INIT pins are tied together in daisy chain configuration, as recommended, the longest delay takes precedence. When daisy-chaining a XC3000 device, the /RESET signal, which is used in XC3000 to delay configuration, should be connected to the /INIT. For XC3000, master mode configurations have a power-on delay of 43 to 130 ms. While other non-master modes for the XC3000 have a power-on delay of 11 to 33 ms.

2. After the power-on delay expires, the internal configuration memory is cleared. This requires ~1.3 us per data frame. The number of frames can be obtained from the Programmable Logic Data Book.

3. A XC4000 or XC5200 device configured in master mode waits an additional 32 to 258 us before re-sampling the /INIT and the configuration mode pins. Use the 258 us value or 0.258 ms as worst case value. The XC3000 samples the mode pins (2 us).

4. The next step is to load the configuration data into the device. If the fast configuration mode is used plus a serial PROM that supports it (i.e., XC17128D or XC17256D), then the FPGA configures up to 8 times faster than if you use the standard serial mode. The first few bits are shifted in at the slow rate until the enable bit is encountered. Once enabled, the FPGA will shift its configuration data in at between 4 MHz to 10 MHz. Again, use the worst-case value of 4 MHz corresponding to 0.25 us per bit. The number of bits can be obtained from the Programmable Logic Data Book. Multiplying 247,960 time 0.25 us per bit. The first few bits are slower, so make a conservative estimation to the overall loading. For XC3000 devices, you should use XC3000 CCLK as 1 MHz (nominal) since you do not have the option of selecting a fast CCLK.

So from the time that Vcc > 3.5 volts to a configured FPGA device should be:

Power-On Delay (Step 1): x ms
Clear Configuration Memory (Step 2): x ms
Master Mode /INIT Delay (Step 3): x ms
Load Configuration Data (Step 4): x ms

TOTAL: x ms

NOTE: Add a 30% guardband above the worst-case values to cover the time the power supply takes to go between 0 and 3.5 volts.

Other items to consider:

Unless the fast serial configuration mode is enabled, the configuration times could be up to 8 times longer. You can reduce the configuration times by setting the CCLK frequency.

Larger devices have more data frames and more program bits and will take a correspondingly longer time to configure.
AR# 3090
日期 09/30/2005
状态 Archive
Type ??????