I am attempting to exercise the interfaces on the Zynq-7000 SoC ZC702 Evaluation Kit.
What tests can be run to ensure that the interfaces are working correctly?
Zynq-7000 Soc ZC702 Evaluation Kit Documentation and Example Designs referenced below can be found on the ZC702 Support page.
Feature | Test Design | Notes |
ZC702 | ||
Configuration Interfaces | ||
Configuration Mode/VMode Pins | ZC702 BIST (XTP180) | Page 16 for QSPI; Page 41 for JTAG |
Configuration PS-JTAG Interface | (Xilinx Answer 46881) | Also covers third-party debugger usage |
Configuration PL-JTAG Interface | (Xilinx Answer 46881) | Also covers third-party debugger usage |
Configuration PMBus Interface | (Xilinx Answer 37561) | Requires TI USB EVM Adapter; see (Xilinx Answer 54022) |
Configuration Digilent JTAG Interface | ZC702 BIST (XTP108) | Page 8 uses the Digilent Interface |
Configuration Xilinx Platform Cable USB Interface | ZC702 BIST (XTP108) | Page 8 uses the Digilent Interface; simply substitute Platform Cable USB and update SW10 settings |
Configuration Quad SPI Flash | ZC702 BIST (XTP108) | Page 15 has user boot from QSPI. See XTP138 for restoring QSPI factory contents |
Configuration SD Card | ZC702 BIST (XTP108) | Page 74. This creates a boot.bin. Copy this to an SD Card, set SW16 for SD mode, cycle power |
Board Feature Interfaces | ||
Board XADC Interface | 7 Series AMS Demonstration (UG960) | Requires AMS101 card |
Board FMC-LPC Connectors | XM105 User Guide (UG537) | Page 29. User Guide for the XM105 Mezzanine Debug card. This card has DS5, DS6, and DS7 which indicate good power to the board. Debug strategies will vary depending on the specific mezzanine card being used. Can also use XTP091. Can also use the ZC702 ZVIK FMC-IMAGEON FMC card. |
Board DDR3 Memory | ZC702 BIST (XTP108) | Page 24 |
Board USB ULPI Interface | ZC702 BIST (XTP108) | Page 28 |
Board Quad SPI Flash (General Purpose) | none available | The QSPIPS peripheral driver has examples that can perform this type of test |
Board USB Serial UART | ZC702 BIST (XTP108) | Page 17. Ensure that the USB UART drivers have been installed |
Board SD Card (General Purpose) | Xilinx Wiki Linux Release | For example: 14.4 - http://wiki.xilinx.com/zynq-release-14.4. This can boot entirely from SD card |
Board HDMI Codec Interface | Zynq ZC702 ZVIK (XAPP794) | Ensure that HDMI monitor is 1080p capable |
Board I2C Interface | ZC702 BIST (XTP108) | Page 19 |
Board 200 MHz differential clock | none available | Drives clock into PL fabric |
Board IIC Programmable clock | Zynq ZC702 ZVIK (XAPP794) | Drives clock to devices on FMC-IMAGEON card |
Board 33.333 MHz PSCLK | ZC702 BIST (XTP108) | The PS uses this clock as the primary reference clock. If BIST works as expected, PSCLK is working |
Board Ethernet PHY | ZC702 BIST (XTP108) | Page 38 |
Board CAN Interface | none available | The CANPS peripheral driver has examples that can perform this type of test |
User Specified Interfaces | ||
User LEDs | ZC702 BIST (XTP108) | Page 18 |
User DIP Switches | ZC702 BIST (XTP108) | Page 21 |
User Pushbuttons | ZC702 BIST (XTP108) | Page 21 |
User PMOD1 Header | none available | Testing requires a Digilent PMOD1 device |
User PMOD2 Header | none available | Testing requires a Digilent PMOD2 device |
Answer Number | 问答标题 | 问题版本 | 已解决问题的版本 |
---|---|---|---|
43748 | Xilinx Boards and Kits - Debug Assistant | N/A | N/A |
50863 | Zynq-7000 SoC - 调试 | N/A | N/A |
Answer Number | 问答标题 | 问题版本 | 已解决问题的版本 |
---|---|---|---|
54012 | Zynq-7000 SoC ZC702 Evaluation Kit - Board Debug Checklist | N/A | N/A |
AR# 54130 | |
---|---|
日期 | 05/21/2018 |
状态 | Active |
Type | 综合文章 |
Boards & Kits |