This answer record contains the Release Notes and Known Issues for the RXAUI Core and includes the following:
This Release Notes and Known Issues Answer Record is for the core generated in Vivado 2013.1 and forward.
Please reference XTP025 - IP Release Notes Guide for past known issue logs and ISE support information.
RXAUI LogiCORE IP Page:
Supported devices can be found in the following three locations:
For a list of new features and added device support for all versions, see the Change Log file available with the core in Vivado design tools.
This table correlates the core version to the first Vivado design tools release version in which it was included.
|Core Version||Vivado Tools Version|
|v4.4 (Rev. 2)||2017.4|
|v4.4 (Rev. 1)||2017.3|
|v4.3 (Rev. 2)||2015.3|
|v4.3 (Rev. 1)||2015.2|
|v4.2 (Rev. 3)||2014.4|
|v4.2 (Rev. 2)||2014.3|
|v4.2 (Rev. 1)||2014.2|
|v3.0 (Rev. 1)||2013.2|
The table below provides answer records for general guidance when using the LogiCORE IP RXAUI core.
|(Xilinx Answer 38279)||Ethernet IP Solution Center|
|(Xilinx Answer 55077)||Ethernet IP Cores - Design Hierarchy in Vivado|
|(Xilinx Answer 55078)||RXAUI Shared Clocking and Reset Logic|
|(Xilinx Answer 55079)||RXAUI Debug Interface|
Known and Resolved Issues
The following table provides known issues for the RXAUI core, starting with v3.0, initially released in the Vivado 2013.1 tool.
Note: The "Version Found" column lists the version the problem was first discovered.
The problem might also exist in earlier versions, but no specific testing has been performed to verify earlier versions.
|Answer Record||Title||Version Found||Version Resolved|
|(Xilinx Answer 70255)||RXAUI v4_4 :Resetdone is not completed on RX in UltraScale and UltraScale+ devices||v4.4||v4.4 (Rev. 2)|
|UltraScale - GTRXRESET required after entering or exiting GT Near-end PMA loopback||v4.0||v4.3|
|(Xilinx Answer 62354)||GTRXRESET toggles when using transceiver debug PRBS inputs||v4.0||v4.3|
|(Xilinx Answer 62351)||7 Series - GTP and GTH - Simulation not supported with UNIFAST model or SIM_GTRESET_SPEEDUP||v4.0||NA|
|(Xilinx Answer 59914)||Additional XDC constraints for the MDIO signal inputs to ease timing closure||v4.1||v4.2|
|(Xilinx Answer 59292)||7 Series - TX Phase Alignment state machine not reset on falling edge of powerdown||v4.0||v4.2|
|(Xilinx Answer 59861)||7 Series GTP- Production reset DRP sequence could get in hung state that requires reconfiguration to recover||v4.0||v4.2|
|(Xilinx Answer 59860)||7 Series GTP - Update to hold off further resets to GTs during reset_in_progress||v4.0||v4.2|
|(Xilinx Answer 58083)||Update to 7 Series GTX Transceiver attribute - RXDFEXYDEN||v2.4||v4.0|
|(Xilinx Answer 56313)||Update to 7 Series GTP reset logic||v3.0 (Rev. 1)||v4.0|
|(Xilinx Answer 55840)||RXAUI v3.0 - Update to RX termination for 7 Series GTP and GTH Transceivers||v3.0||v3.0 (Rev. 1)|
|(Xilinx Answer 55900)||Verilog - If using TXPRBSFORCEERR input, the connection to GT1 in Verilog needs to be corrected||v3.0||v3.0 (Rev. 1)|
|(Xilinx Answer 55229)||Artix-7 - Critical Warning - No cells match DRP path for false path constraint||v3.0||v3.0 (Rev. 1)|
|(Xilinx Answer 55009)||7 Series GTX/GTH/GTP Transceivers - TX Sync Controller Change for Phase Alignment in Buffer Bypass Mode||v2.4||v3.0|
|(Xilinx Answer 53561)||Artix-7 - RX Reset Sequence Requirement for Production Silicon||v2.4||v3.0|
|(Xilinx Answer 50848)||7 Series GT Transceivers - Updates may be needed to GT wrapper files||v2.4||v3.0|